You need to learn how to use only a single set of functions to be able to program most National Instruments data acquisition hardware in multiple programming environments. NET library cannot be instantiated directly. It also greatly simplifies programming such applications. This level of performance is possible because of memory-mapped registers. The different instances of the function allow for the type of generation analog or digital , the number of virtual channels, the number of samples, and the data type to be selected. If you do not have the original media that was shipped with your products, visit ni. This tool helps you create your applications without programming through a graphical interface for configuring both simple and complex data acquisition tasks.

Uploader: Zulukinos
Date Added: 23 September 2012
File Size: 48.79 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 25455
Price: Free* [*Free Regsitration Required]

Learn 10 Functions in NI-DAQmx and Handle 80 Percent of Your Data Acquisition Applications

These instances correspond to the specific type of measurement or generation the virtual channel s perform. In the following figure, DAQ Assistant is configured to perform a finite strain measurement. In the running state, the task performs the specified acquisition or generation.

For finite acquisitions, by specifying a number of samples per labvieq of -1, the function waits for all of the requested samples to be acquired and then reads these samples. Furthermore, since the number of samples per channel input has been wired to a constant value of 10, each time the VI executes it will read 10 samples from each virtual channel.

Connect and Set Up Hardware Next. Attribute [CVI] Property [. This site uses cookies to offer you a better browsing experience.

  CLIE SJ20 DRIVER

NI-DAQmx and LabVIEW Compatibility

This programming pattern is similar to the pattern used throughout the. Analog output channels— AOChannel class.

Finally, the active edge of the sample clock is set. Call it after a write or start function. The data acquisition applications you build using NI-DAQmx benefit from an architecture designed to maximize performance.

This begins with an efficient state model that eliminates unnecessary reconfiguration. The following LabVIEW block diagram demonstrates a situation where the NI-DAQmx Start function does not need to be used because the analog lahview generation only consists of a single, software-timed sample.

Installing LabVIEW and NI-DAQmx – National Instruments

Although it is not always required, using the NI-DAQmx Start Task function to explicitly start a task involving a hardware-timed acquisition or generation is preferred. To set the source of the sample clock, the rate of the sample clock, and the number of samples to acquire or generate use the Channel. Rate this document Select a Rating 1 – Poor 2 3 4 5 lwbview Excellent. To create a channel, you can use one lxbview the many create channel methods on the channel collections.

When a task is not specified, the function creates a task. Then, the source of the sample clock is read.

This function lavbiew be used to ensure that the specified acquisition or generation is complete before the task is stopped. To get an instance of the DaqStream class that corresponds to a particular Taskuse the Stream property.

As noted above in the Timing section, many properties are set from within subclasses and collections inside of the Task object.

One of the ways NI-DAQmx saves development time is by providing an API that requires only a small number of functions to expose the majority of its functionality. Back to Top 2. Below is a snippet that shows how to use the function for a digital start trigger coming in on PFI0 and looking for a rising edge on that line.

  DVD GSA-T20N DRIVER

As mentioned in the Introduction, the state model used by NI-DAQmx eliminates raqmx reconfiguring to obtain a high level of efficiency and maximize performance. If the acquisition or generation does not complete within this amount of time, the function exits laview an appropriate error is generated.

NI-DAQmx Software – National Instruments

NI-DAQmx Properties provide access to all of the properties associated with a data acquisition operation. You need to learn how to use only a single set of functions to be able to program most National Instruments data acquisition hardware in multiple programming environments. Instances of the NI-DAQmx Read function that are capable of reading multiple samples include an input to specify the number of samples per channel to read when the function executes.

Prev Choose a Platform.

If the task is currently running, the function first stops the task and then releases all of its resources. This tool helps you create your applications without programming through a graphical interface for configuring both simple and complex data acquisition tasks. Furthermore, a custom scale can be applied to many types of virtual channels.

A reference trigger establishes the location in a set of acquired samples where pretrigger data ends and posttrigger data begins.